产品分类
联系我们
电话: 0835-554845
传真: 0835-554845
邮箱: dfcwmz@disco-inferno.net
地址: 四川省雅安市
新闻中心

正确选择选择气液增压泵四步骤

选择气液增压泵

1.工作压力和流量

1. The working pressure and flow rate

气液增压泵和动力单元的工作压力参照驱动气压为0.48Mpa时泵输出压力和流量.如果泵的最大输出压力大于所需的工作压力,这就要考虑安全措施.对于最大输出压力,请参照产品目录中的"静态下驱动气压力和输出液压近似比率表".动力单元的选型与泵一致.对于工作流量,请参照产品目录中的"性能曲线图".

Pneumatic booster pump and power unit pressure reference drive pump output pressure and flow when pressure is 0.48 Mpa. If the maximum output of the pump pressure is greater than the required working pressure, this is about to consider safety measures. For maximum pressure, please refer to product catalog "static hydraulic driving gas pressure and output approximation rate table". Consistent with the pump in the selection of power unit. For work flow, please refer to product catalog "performance curve".

2.驱动气体的压力和流量

2. To drive the gas pressure and flow rate

气液增压泵和动力单元在连续工作时使用的驱动气压不超过0.69Mpa,在间歇工作时可达到1.03Mpa.在最佳性能状态时气动泵的耗气量,请参照所需驱动气体流量表.

Pneumatic booster pump and power unit used in continuous work of driving pressure is not more than 0.69 Mpa, when intermittent work can reach 1.03 Mpa. In the best performance of the gas consumption of the pneumatic pump when, please refer to the required drive gas flow meter.

3.输送液体介质

3. The conveying liquid medium

气动增压泵泵输送的液体介质是气动增压泵的选型中着重考虑的部分.液压部分的材质和液压密封圈是由输送的液体介质所决定的.泵可用油、水和大多数液体介质.标准泵的主要液压密封圈是丁橡胶和聚氨酯,单向阀座采用特氟龙密封.其它密封材料包括碳氟化合物和亚乙基丙烯,这些密封材料主要用于输送的特殊介质.请向工厂或当地的分销商咨询密封材料选型.

The pneumatic booster pump pump liquid medium is emphatically considered part of the pneumatic booster pump selection. The material of hydraulic parts and hydraulic pressure seal is determined by conveying liquid medium. Pump oil, water, and most of the liquid medium. Standard pump hydraulic seals are mainly butyl rubber and polyurethane, one-way valve seat adopts teflon seal. Other sealing materials including fluorocarbon and ethyl propylene, these special sealing material is mainly used for conveying medium. Please consult factory or local distributors seal material selection.

4.气液增压泵可接受的体积和重量对于某些的应用,气动增压泵和动力单元的外形尺寸和重量也要重点考虑

4. The volume and weight of the pneumatic booster pump is acceptable for some applications, the overall dimensions and weight of the pneumatic booster pump and power unit will consider mainly

BACK

版权所有:四川省庆优自吸泵有限公司, All rights reserved

地址:四川省雅安市  电话:0835-554845  邮箱: dfcwmz@disco-inferno.net